Search my site

Amazon AStore

A selection of relevant products available direct from Amazon. You'll find lots more practical info in various articles on my website.

Visit My Amazon AStore


Key Web Links

Entries in fluorescent inverter (1)


Homebase round mirror inverter repair (Part 2)

To recap, having swapped the light tube only to find it still wouldn’t light, I discovered that the original electronic ballasts are no longer made, not even by Landlite. It's this that gives the light its instant-on feature without any flickering, but it seems the EB-56 ballast is prone to failure and a few people have had problems with them.

Rewiring the whole lot using a traditional ballast and starter isn't trivial. The only other option is to try a Chinese-made 40W circular fluorescent tube inverter instead, and the very thing was being sold on ebay (if you import from Hong Kong) as well as on Amazon.  Otherwise, consider upgrading to a more modern and reliable LED bathroom mirror such as these LED Bathroom Mirrors on Amazon.

The Chinese inverters aren't CE-marked (not that CE marks count for much on some Chinese imports anyway) but having scoured the planet searching for a new inverter, this was all that's available. They're £6 each and Amazon delivered a couple in 48 hours. (I got one for spare.)

Comparing Landlite EB-56 inverter (click to enlarge)As they're not as big or heavy as the original Landlite EB-56, they’ll fit inside the mirror without a problem.  Read on...

DIY instructions to repair a faulty Homebase mirror lamp inverter

Switch off the mains at the fusebox, or switch off the relevant ring-mains or (in my case) lighting circuit breaker. If the mirror’s above a sink, put the plug in the plughole in case any screws fall in.

Remove the four screws holding the glass on the metal base, and gently pull off the mirror.
  Mirror removed, revealing the tube and inverter (click to enlarge)

Landlite EB-56 inverter and terminal block (click to enlarge)Unscrew the terminal block cover, loosen the cable cord grip screws and disconnect the Live (brown) and Neutral (blue) wires going to the old inverter. As the Live goes to the pull-switch, that must be unscrewed  to get to the screw terminal, while Neutral goes to the main terminal block.

Terminal block and pull-switch housing (click to enlarge)Also disconnect the Earth (green/ yellow) wire that goes to the old inverter. Leave the light’s main earth wire in place, safely connecting the light's metal chassis to the Earth terminal block.

Remove the old inverter's Earth, Neutral and Live wires. The pull-switch has to be unscrewed to access the Live terminal (click to enlarge)

Terminal block minus the old inverter's wiring (click to enlarge)

Note the replacement inverter needs no Earth wire; that’s OK as the old Landlite inverter simply had  extra filter circuitry connecting to Earth.

Pull off the fluorescent tube’s connector plug. Remove the two mounting screws and the old inverter will come away.

 The old inverter removed. The lamp's earth wire remains connected as shown (click to enlarge)

The new inverter is smaller and doesn’t fit the two existing mounting holes. Typical. As it only weighs a third of the original one, I chose to mount it using the original screw on the right handside only. The other option is to drill and tap a new hole in the base for the inverter’s lefthand mounting tab, which I thought was over-elaborate as the new inverter is fairly lightweight and it isn't going anywhere.

 The new inverter in situ, held down with one screw. Unused screwhole circled in red. (click to enlarge)

Connect the new inverter’s Live (red) wire to the pull-switch, feeding it through the cable grommet and cable grip in the terminal block. Connect the Neutral (white) directly to the Neutral screw terminal block. Ensure none of the wires is trapped anywhere when the pull-switch is screwed back down, and that the switch operates smoothly without the cord jamming. Again, double check the light's earth wire is still connected properly to the main terminal block.

 New inverter in place and the tube is reconnected. Note the earth wire. (click to enlarge)

The fluoresecent tube can be reconnected, moving it around on its clips if necessary so the inverter’s connector lead can reach it. Finally, replace the terminal block cover. You can now turn on the mains and test the lamp.

 After re-assembling the terminal cover, turn on at the mains and test (click to enlarge)

Finally, check the rubber seal going around the edge is located properly to protect against moisture, and then the mirror can be screwed back into place. Job done!

A £6 inverter isn't quite as good as the original but it's good enough and has given the light a new lease of life.

  • Information was correct at time of writing,  13th Feb. 2014
  • Also see my piece on upgrading a 32W Circline ring fluorescent ceiling light here
  • The unit's mains wires (red and white) don't always tally with the label. You might want to read my item about this discrepancy on the JL-EB40Y here.